Our commercial roof repair services in Merrillville cover flat membrane roofs, steel roofs, hard-to-find leaks, and busy plant roofs.
Pick the card closest to your roof. Each of these commercial roof repair services in Merrillville matches new material to what is already up there, from membrane type to panel rib.
Low-slope roofs that hold water after storms or leak at seams and drains. We cut out wet insulation, patch with the same membrane type, and rebuild drain flashing so water leaves the roof.
Exposed-fastener and standing-seam steel roofs that drip along screw lines, laps, or ridge caps. We refasten, swap rusted-through panels for matching profiles, and reseal laps and wall flashing.
Leaks that return after earlier patches, appear only in hard rain, or show up far from where the roof failed. We trace the path, repair the source detail, and photograph it.
Large roofs over production floors where a leak stops a line or soaks stock. Work is split into sections, timed with the facility manager, and focused on fans, joints, and drains.
Most commercial roofs in town are either a membrane laid over insulation or ribbed steel on purlins. The two fail and get repaired in different ways.
Describe what you see inside and what kind of roof it is. We can usually tell which repair fits on the first call, then confirm it on the roof.
Call UsSend every address on the property. We will walk each roof in one trip and list the repairs building by building.
Send roof details for an estimateInterior stains, drips, and wet stock are mapped first and measured from the walls. The roof above them is then walked with that map in hand, starting directly overhead and moving uphill along the deck.
Membrane type, panel profile, insulation thickness, and deck material get identified on the first walk. That way every patch, screw, closure, or replacement panel matches what is already on the building.
Moisture readings and core cuts on membrane roofs, or a screw-by-screw and lap-by-lap check on steel, show how far the problem reaches beyond the spot that dripped.
Welded or taped patches, rebuilt drain seals, new fasteners and washers, or same-profile panels go in where the old material failed, with flashing redone at any curb or wall the water reached.
Owners get photos of the leak source and the finished roof repair, plus short notes on any seams, drains, or curbs that need watching before the next season.
How owners choose between the four repair services.
Start with the roof type and what you see. Flat membrane roofs with ponding or seam leaks fall under flat roof repair, steel roofs with lined-up drips under metal roof repair, and plant roofs with fans and joints under industrial repair.
A leak you cannot place goes to leak tracing first, and the trace decides which repair follows. When in doubt, describe what you see and we will sort it out on the first call.
Often it does. Many buildings have a flat office section, a steel warehouse, and equipment on the roof. A single walk covers all of them, and the write-up lists each repair under the roof area it belongs to.
That keeps the flat section, the steel section, and the equipment zones from being priced as one job when they need different materials.
Repairs here are almost always on roofs someone else installed. Matching the existing membrane, panel profile, and fasteners is the whole point, so the repair ages with the roof around it.
A TPO roof gets a welded TPO patch, an EPDM roof gets primed tape, and a ribbed steel roof gets panels in the same rib pattern and gauge.
You will hear that plainly, with moisture readings and photos showing why. Small repairs can still stop leaks while a replacement gets planned and budgeted.
Those stopgap repairs are kept small and listed separately, so money is not sunk into a roof that is about to come off. The photos and readings also help when you talk with a lender or insurer about the new roof.
Yes. The estimate visit covers walking the roof, finding the leak sources, and writing up the repairs. There is no charge for the visit or the write-up.
You get the leak sources, the repairs each one needs, and the photos, and you decide what to do from there.
Timing depends on weather, roof access, and materials for your roof type. Active leaks get a temporary fix as a first step, and the permanent repair is scheduled once the area is dry.
Winter repairs use cold-rated tapes and fastened patches, with a final patch in spring where full adhesion needs warmer weather.
Tell us the roof type and where water shows up inside. We will match the repair to the roof and walk it with you.